3 according to state I whereby the tire packing machine, distinguished for the reason that explained tread deal model (3) consists of a symmetrically attached to the body (I) of the two shaft seating (13) and installed on the shaft seating (13 ) throughout the shaft (14), the shaft (14) are attached to the left arm (15), the arm (15) is fitted involving the vertical beams (16), beam (16) from a bolt fixed on the turning arm (15) around the ray (16) is supplied with packing adhesive tape fittings (17).
As reported in state I whereby the wheel packing machine, described for the reason that mentioned tread elevate device (4), contains a top to bottom route of the two cylinders are connected in range, the top of the the cylinder (18) with all the holder (I) attached, and also the lower cylinder (18 ‘) is associated with a horizontal information rail (19), horizontal side rails (19) is attached to two sliders (20), slip (20) movable alongside horizontal side rails (19) slip, the glide ( 20) attached to a tire provided with inwardly flip pawl (21).
5 according to claim I in which the wheel packing machine, distinguished for the reason that mentioned exterior connecting means (5) comprises two symmetrically arranged arm (22), left arm (22) coupled to the higher finish by a shaft Rack (I), the arm (22) connected to a lower knife owner (23), two left arm (23) around the holder (23) in accordance with pushing, the instrument mind (23) is provided with about three guide lines , each information groove are respectively attached to the bezel (24) or heating the adhesive dish (25), baffle (24) along with the home heating the sticky dish (25) – equally comes to an end by a springtime (26) coupled to the bottom part in the guide groove, baffle (24) is greater than the duration of the heating system the adhesive platter (25) in size, every single blade holder (23) comes with two heating system the adhesive dish (25), is also mounted on the reducing blade blade (27) , shear blade (27) located between the two home heating the adhesive dish (25), among two resource head (23) relative to the positioning of pushing indicates in wheel bundle (3) beams (16) beneath the maximum placement.
As stated in declare I wherein the tire packing machine, described for the reason that explained flange signifies (6) makes up two symmetrically disposed installation foundation (28), mounting foundation (28) from the picking up screw (29) fitted delivering implies inside the top to bottom basic wheel (9), the two installation program (28) implies are placed in two parallel straight tire delivery service sequence (11) each side in the mounting platform (28) is mounted on the auxiliary body (30 ), auxiliary body (30) attached with all the centre manual shaft (31), the manual shaft (31) is attached to movable down the manual shaft (31) the slipping bracket (32), glide the bracket (32) is supplied using a plurality manual shaft (31) as being the middle outward in a guide groove (33), auxiliary body (30) from the guideline groove (33) is attached a corresponding situation strut (34), the guideline groove (33) is attached over the internal manual lines (33) slidably movable block, the movable obstruct is attached to the active handle (35), the energetic handle (35) – stop in the movable prevent with the shaft interconnection, the lively lever (35) from a shaft and the middle strut (34) is connected , flange indicates (6) attached to the bottom further comprises (9) situated on the promoting indicates (10) underneath the lover (36).
As reported in claim 6, in which the wheel packing machine, recognized for the reason that explained guideline groove (33) to the about three information lines (33) inside the manual shaft (31) like a middle in the direction of the 3 o’clock route, correspondingly, 9 o’clock, 12 o’clock, wheel lever in the Agency’s routines (35) is divided into a movable rod (35 ‘) as well as two movable rod (35 “), a movable rod (35’) through the shaft with two Levels the lively lever (35 “) attached to a movable rod (35 ‘) is fitted to the top level platter wave sweep (37), the additional movable rod (35”) as well as the rod (34) and also the movable prohibit, linking implies with all of those other place of the movable rod (35) hooked up likewise; others position the movable rod (35) is also attached to the additional movable rod (38), the energetic handle (35) can also be linked to the surface of wave sweep dish (37), the auxiliary movable rod (38) – finish in the influx sweep platter (37) with a shaft linked to the auxiliary movable rod (38) using a shaft as well as the opposite end in the strut (34) attached to rod (34), the active lever (35), the secondary movable rod ( 38), waves sweep plate (37) produce a parallelogram railing firms, surf sweep dish (37) carries a work surface brush.
As claimed in claim I wherein the wheel packing machine, distinguished because stated inner adhesive indicates (7) are mounted on the flange comprises indicates (6) two installation foundation (28) around the two linear guide side rails (39), linear manual (39) are put in over the linear guide (39) moving bracket (40), holder (40) in the top use a compact (41), into the briquetting (41 ) inside a hard drive-formed tension plate, two stretches clamps (41) in the strain platter relative to nip.
(10) according to claim 8, wherein the tire packing machine, characterized in that said pressure plate, respectively chopping platen (42) and the cutting pressure plate (43), the cutting platen (43) smaller in diameter than chopping platen ( 42) the diameter of the cutting pressure plate (43) extending into the side clamps (41) mounted on a lid-shaped blade cover (44) and blade cover (44) is mounted within an annular heat cutter (45), cyclic heat cutter (45) in the cutting pressure plate (43) on the outer periphery, into the clamps (41) is provided with a through hole, the through hole is connected to waste recovery, including recovery of the waste into the clamps (41 ) connected via the trachea, air pump connected with the trachea.
According to claim I wherein the tire tire package packaging machine, characterized in that the packaging process is as follows, 10 Use: 1) standing upright up-right into the tire tread straight shipping and delivery indicates; 2) moved on the wheel tread wrapping product, the unit will elevate wheel tire elevate device package fetal movements around the tire tread, the tire tread wrapped in packing adhesive tape on; 3) point out wheel means the tire straight down, the external packaging adhesive adhesive tape reducing tool and two conclusion connecting, bonding product while the outer engagement ring will shut down other conclusion of your packing adhesive tape sticky relationship with the deal tire system; 4) wheels mailed towards the wheel interior connecting device, system packaging tape flanging advantage turning on the wheel inner group the packaging tape within the sidewall; 5) inside connecting product will roll over to the tire inner packaging with sticky; 6) car tires transported to cooking tightening up gadgets, home heating packing adhesive tape, packing adhesive tape to tighten up the , firmly deal with in the wheel.
Explanation converted from Oriental
Tire packing machine and packing method
 The present technology concerns a packaging machine and packaging strategy, especially, is actually a packaging machine for packaging wheel along with a tire employing this packing machine packing method.
Which uses ribbon packing materials, wrapping machine with a tire package material circle around the ribbon, wrapped around the edges overlapping tires, packaged this way because of overlapping winding, a large amount of packaging materials, packaging costs are high, serious waste of packaging materials and packaging easy to loose, poor stability, packaging, slow, packaging production is low,  The tire packing methods are available for the wound.
 earlier patent “Wheel packing . 3) the design of a tire packaging equipment, use of non-wrapped style packaging, but there are still many shortcomings, packaging molded together under the upper die of packaging, packaging tires need accurate positioning, position requirements, packaging technology requirements, the connection length long, the upper die and the lower die junction is located in the outer tread last week, totally exposed on the outside of the tire transportation prone to damage in the process, a solid weak, and the packing effect unsightly outer adhesive as a whole, produce more waste packaging, packaging material utilization is low, the packaging cost is high.